How To Build A Gable Roof Patio Cover

Vinyl Patio Cover Cost

The average costs of a vinyl patio cover are between $5 and $13 a square foot installed. Vinyl is one of the lowest-cost options for any cover. It is easy to work with and comes in many different styles. It is also fairly low maintenance but is not as durable as other materials. Vinyl can be made into pergolas, lattice, panels, and many other roofing styles. You may be limited in colors and overall patterns.

Insulated Patio Roof Panels Cost

The cost of an insulated patio roof ranges from $26 to $59 a square foot installed. Insulated patio roof panels help prevent the patio from becoming overheated. This is a particularly good idea if your patio has some type of enclosure or walls like a gazebo. Insulated panels can be made of fiberglass, aluminum, or wood. They come in several different styles and can be added to many different types of roofs or covers. The material being insulated and the overall structure style dictate the final cost.

Step 2: Dig Post Holes

It was a little bit difficult to figure out where to dig the post holes. I wanted them to be exactly 9.5′ from the roof edge, but the houses foundation was recessed 2′ from the roofs drip edge and stuck out 26 from under the bay windows. How was I going to get an accurate measurement? All sorts of neat tools I saw people use on TV shows and formulas from various math classes flashed through my mind. Here’s what I did:

• I stood up up a couple of posts at the roofs edge, using a bubble level to make sure they were perfectly upright.
• Then I measured and marked nine and a half feet on a couple of joist boards and laid them on the ground, with one end by the upright posts and the markings on the other end showing where the hole should be dug. I did this at both edges of the ledger board and laid two more ten-foot joist boards between them.
• I then used my square, or angle iron, to make the corners square.
• I marked the spots for the three post-holes, with the middle post-hole going where the two 10 foot joist boards met.
• I then measured corner to corner, one way and then the other, and made slight adjustments until both measurements came out the same. With the exact centers for the post holes marked, I marked 18 circles around them because I planned to dig the holes 18 deep and wanted them to be as wide as they were deep, in accordance with local building codes.

• Make sure the post extensions are even.

  Where To Attach A Patio Roof Ledger

  On a one-story house, it is often best to attach the ledger for a patio roof just below the houses eaves.

  On a two-story house, you can usually tie the ledger into a band joist , located between the floors, as shown below. Find the band joist by measuring down from a second-story window.

  Browse Tools for This Project on Amazon

  Porch Roof Cost Calculator

  

  Building a porch roof costs $16 to $30 per square foot. For a 200-square-foot structure, this ranges from $3,200 to $6,000. A significant portion of the total depends on the material, which usually matches whatever you have for the rest of the house.

  Roof Construction Prices Per Square Foot

  Frame

  • Cost to screen in a porch: $5-$7 per square foot

  How To Build A Gable Porch Roof

  Gable roof is the most commonly found type of porch roof. It has a shape of a triangle with a certain pitch and sloped sides. Whether you are thinking of adding a gable porch to an existing roof or building a new one, it is beneficial to help your shed water and snow.

  Here is the guide on how to build a gable roof over a porch you may follow:

• Decide where the posts of roof support are going to be. Put a mark on the determined locations on the roof deck and the deck areas on the decided spots, so you can set a hole, concrete footing, and set the roof support posts.
• On the ground, dig the holes for every post spot with a width of 12-18 and a depth of 18. Set concrete in cylindrical shape within the hole and then cover with concrete. Arrange post anchors while the concrete hasnt dried up yet. Then let it sit for at least 24 hours.
• Size and trim support posts in 6 x 6 that suit the dimensions of the roof. Install the support posts on the anchors and set them loosely using bolts and nuts. You need to ensure that the posts are upright by bracing them tentatively while securing the bolts and nuts.
• Size and trim two lumber pieces in 2 x 8 that suits the distance between each support post. Lift the 2 x 8 lumbar pieces with the help of someone else, and nail one of the 2 x 8 lumbar pieces temporarily to every side of the support post, but make sure the nails can be removed easily later on.

• Step 8: Structure The Roof

  To structure the roof, take your 2×6 boards. You can cut them down as needed. Since they will overhang a little bit over the patio, you need to make sure that you do not cut them down at the same length as the patio.

  They have to be a bit longer than the patio. If you have cut them down, you can begin to arrange them so that they cross the joist beams and create a perpendicular pattern.

  Make sure they are evenly placed across the top of the patio. Keep them in place by installing galvanized deck screws.

  Are Roof Decks Worth It

  Most homeowners will agree that a roof deck is worth the price. Not only will it protect you from the elements when youre outside, but it will also improve your homes curb appeal and resale value if youre looking to sell it in the future. Contact your local roofing contractor to see what they can do to help.

  Fastening To Masonry Walls

  Cedar patio cover build free estimates 817-631-9788

  Anchor a ledger to a masonry wall with expanding anchor bolts. Begin by marking a line across the wall for the ledgers top edge. Drill holes for the expanding anchors every 16 inches or as specified by local codes, insert the anchors, hold the ledger in place, and tap it with a hammer to indent the anchor locations on its back face.

  Remove the ledger, and drill bolt holes where the bolt tips have left marks. Push or hammer the ledger back onto the bolts, recheck for level , add washers and nuts, and then tighten the bolts.

  How To Build A Roof Over My Existing Deck

  Summer may be over, but its the perfect time to start building a roof over your deck for next years sunny season. If youre looking to enjoy the great outdoors right from your backyard while still getting some relief from the sun or rain, a roof over your deck or patio is the perfect solution.

  So, how do you go about it? You may want to just get it over with and do it yourself, but sometimes its better to hire a professional who can get it done efficiently. In this blog, were going to cover the benefits of building a roof over your deck, how to do it, and the average costs. Here at Legacy Service, we will do all we can to help you perfect your homes exterior. If you have any questions or would like to schedule an appointment with us for a roof replacement, give us a call at 215-798-9790 or fill out a contact form here.

  Fastening A Patio Roof To The House

  Expert advice on how to attach a patio roof to a house, with step-by-step instructions and construction diagrams.

  A house-attached patio roof takes advantage of the houses structure by supporting one end of the roof on a ledger mounted horizontally to the house. The ledger, typically a 2 by 6, is usually designed to hold one end of the patio-roof rafters. Locating and mounting the ledger is normally a fairly easy process; the ledger should be attached before the foundation is built for a deck, patio roof posts, and other structure.

  How Do You Attach A Gable Roof To An Existing Roof

  Adding a Gable Roof to an Existing Roof To tie into the side of an existing roof , put a new roof truss on the walls of the addition , brace it upright, then snap chalklines on the shingles to mark the center line of the new roof valleys, where old and new roofs will connect.

  Patio Designs With Images Covered Design Backyard

  

  Building a deck with a gable roof. Decking Patio Half Gable Roof Deck Covers Designs Hip. How To Build A Gable Roof Patio Cover Mycoffeepot Org. You must know this stuff before build a deck porch or outdoor wood project duration stumpy nubs views.

  Ad Search Build A Decking. How To Build Gable Roof Trusses. What is the easiest roof to build.

  Get Results from 6 Engines at Once. Ad Separation is required. Follow these steps to build one of these functional roofs yourself.

  The cost will vary depending on the professionals hired materials used square footage and weather conditions. Some kind of roof line attached to the garage would be needed. Porches need to be designed to support 80 lbs per square foot compared to 55 lbs per square foot for decks.

  Get Results from 6 Engines at Once. Building a gable roof over your existing deck will make it more comfortable providing shade and shelter from the rain design of also allow. Join VIP for Cottage Shed Planspdf download.

  The gable design of the roof will also allow for excellent rain and snow runoff in wet climates. May 13 2013 Building a gable roof over your existing deck will make it more comfortable providing shade and shelter from the rain. The benefits of aaa glass patio and deck covers backyard covered patios can provide a special outdoor living space providing transition from indoors to an.

  Build Aroof Over A Deck Decks Building A Shed Roof Building A Shed Patio

  Covered Porch Design Patio Design Diy Porch

  Step 4: Assemble The Frame

  The rest of the frame I assembled on solid ground, not wanting to hold everything in place with one hand while installing decking screws with the other.

• Cut four braces at precisely 45-degree angles. I cut them from a single 10-foot long 2×10 board. I measured the width of the board with a ruler, then marked that length from the end of the board and cut from there to the corner to make a triangle of wood that was exactly the right shape. I measured the short sides of that wooden triangle-shaped block and they were exactly the same so I knew it was cut at a 45-degree angle. I used that to mark the lines I would cut to make the braces. I made the two outside braces three feet long at their outsides and the two inside braces two feet long at their outsides.

• Joists

  Photo 8: Level And Mark The Beams

  Extend the posts with 2×4 and 2×6 cedar so that they project beyond the top of the ledger, nailing every 4 in. with 16d casing nails up to the beam height. Cut a 2×10 beam member to length and shape the end. Rest it in the joist hanger, level it and mark the height on the post. Cut only the post 2x6s at that height with your circular saw. Cut the center 2×4 9 in. higher .

  Use .60 foundation-grade treated 2x4s and 2x6s for the lower post sections and the footings . You may have to special-order them, but the added longevity is worth the money and trouble. For the above-ground base skirt framing and sheathing, standard .40 treated material will work just fine.

  The base skirts are designed to float, that is, slide up and down the fixed posts that they encase. Thats especially important when they rest on a slab or stone surface in cold regions where frost can lift patios when the ground freezes. The skirts can move up and down during freeze/thaw cycles, but the posts, which extend below frost depth, stay putwithout lifting the entire structure. So when you frame and trim the pilaster base skirts, make sure everything fits loosely.

  If the posts have to penetrate a concrete or stone surface, cut a 20- in. square hole for digging the footings . Use a circular saw with a diamond blade and dont worry about making it pretty; the skirt will cover the hole. To prevent settling, just be sure to pack the soil well as you backfill around the posts.

  Flashing A Patio Roof Ledger

  Unless it will be protected from rain by the houses eaves or a solid roof, a roof ledger that is fastened directly to a house with wood siding should be capped with galvanized metal Z-flashing that tucks up under siding to prevent water from seeping in behind it.

  Where integral flashing isnt possible, such as on a stucco wall, use Z-flashing and caulk the top edge. This is a job you must do before fastening the overheads roof rafters in place.

  You can buy L- or Z-shaped flashing or bend it yourself. To bend sheet-metal flashing, make a form by clamping two 2 by 4s together on each side of the metal, and then hammer the metal to create a sharp edge at each fold.

  Fit the flashing in place, caulk the top edge, and nail it with galvanized nails long enough to penetrate at least 1 inch into the structural members. Then caulk the nail heads.

  If the house is sided with shingles or lap siding, simply slip the metals top edge up under the bottom edge of the shingles or siding as far as possible.

  NEXT SEE:

  What Is A Freestanding Patio

  How To Build A Gable Patio Roof – DaddyGif.com (see description)

  A freestanding patio is a covered patio that sits on your backyard without being supported by the house or other buildings.

  Unlike the ones that rely on the roof, this patio features, at least, four posts that support the cover. That is why it is called a freestanding patio cover.

  Since it sits on its own, it is varied in sizes and heights. It means you can build any patios that suit your style very well.

  What Is The Roof Over A Deck Called

  The roof over a deck is usually called a patio cover. This attached structure provides protection from sun and rain and can either have a solid or open roof. Pergola is another name for deck or patio roofs. This is typically characterized as an open roof thats supported by posts or columns. They provide filtered shade to outdoor living areas.

  Fiberglass Patio Cover Cost

  The cost of a fiberglass patio cover is between $16 and $39 a square foot installed. Fiberglass is one of the materials considered to be the gold standard by many contractors. It is attractive, durable, and very easy to maintain. Fiberglass comes in lattice, pergola, panel, and many different styles, colors, and shapes. Fiberglass is sometimes combined with other materials to give it greater durability. It is also a good insulator, making it a useful option for roofs where the sun is directly overhead.

  Step 9: Double Check For A Better Freestanding Patio Cover

  Now you have the structure of a freestanding patio cover. You can begin to cover the patio with the materials of your choice such as lattice wood, translucent fiberglass, wood and shingles, metal panels , boards and netting, or canvas shade sails.

  The structure that you have just made is the simplest one. There are various kinds of structures available that suit your patio very well.

  But you have to remember to double-check the level of the whole patio before adding the roof. For more freestanding patio cover ideas, check out these ten fantastic patios.

  Average Cost To Build A Roof Over A Deck

  

  Decks and patios enhance any homes living and entertainment space, and adding a roof to that extension can further increase their function and value. However, were sure youd like to know the average cost to build a roof over a deck before you make any decisions.

  Unfortunately, we wouldnt be able to tell you how much it would exactly cost to add a roof to your deck without scheduling a consultation and coming to your home. But we can give you an average range of prices that it would most likely fall within. They include:

  • Adding any deck covering or enclosure will typically cost between $1,000 $10,000.
  • Adding a covered roof to your deck will typically cost between $3,000 $10,000.

  The cost will vary depending on the professionals hired, materials used, square footage, and weather conditions.

  Make The Patio Roof A Little Bit Higher

  It is almost similar to the first method, but to make the patio roof a little bit higher, you will need to remove the house gutter and place the back channel a bit higher.

  Because the gutter is removed, you will need to install transfer flashing from the roof of the house to the patio. It allows you to add over a hundred millimeters of extra height.

  Cost To Build A Covered Patio Attached To A House

  The cost to build a covered patio attached to a house ranges from $500 to $25,000 on average. A small bistro patio with a sailcloth cover is at the lowest end of this cost. An outdoor kitchen patio with a full roof is at the high end. Because patios come in so many different sizes and styles, the cost range is large. Attaching a patio and cover to the house allows more options. Attached pergolas 1 and awnings can be less expensive than freestanding gazebos.

  Photo 15: Cut The Curved Braces

  Cut two 4-ft. lengths of 2×10 and tack them between the 2×4 rafter and ceiling tie parts to lay out the curved decorative braces . Mark the lengths at the 2x4s. Bend and clamp a thin board and trace arcs about 7-1/2 in. apart on both sides. Cut them with a circular saw and jigsaw and nail them into place.

  Plastic Freestanding Patio Cover Idea

  Patio Roof Cover One Day Build – Time Lapse

  Having breakfast outdoor is just a terrific idea to spend your weekend. You do not need to take a road trip to make it true.

  You can do it right in your covered patio in your backyard. This freestanding patio features a plastic cover that sits perfectly on the beamed ceiling.

  It helps you keep the glare and heat at bay. You can still enjoy your breakfast outdoor even though it is raining because the cover is water resistant.

  The good thing about plastic materials is they are usually less expensive than wooden materials.

  Therefore, this freestanding patio cover will just make a perfect shade without burning a hole in your pocket.

  Customized Free Standing Patio Covers In Orange County

  With an outdoor barbecue and a sparkling swimming pool overlooking the breathtaking Southern California landscape, this customers patio was already a focal point for entertaining. A freestanding patio cover added the ability to host gatherings in all conditions. Ceiling fans hang from the solid aluminum cover, creating a soft breeze on even the warmest days. Positioning the cover next to the barbecue area provides an ideal dining area where guests can enjoy a meal while marveling at the picturesque surroundings.

  We are thrilled with the way this gabled patio cover has provided this property with an elegant poolside retreat. From the classic elegance of the custom-built square columns to the soft glow of the modern lighting, this solid aluminum patio cover creates a space where the customers can welcome the quiet morning or guests can mingle at night.

  Our Location

  This durable, stylish gabled patio cover is just one of many projects Patio Warehouse has installed for customers in cities such as Yorba Linda, Mission Viejo, Anaheim, and Lake Forest. If you are interested in a gabled patio cover or any of the other covers we offer, contact us today to schedule a free, in-home consultation. In this project, youve seen what we can do for other customers. Its time to see what we can do for your Orange County home!

  To view more images of this project visit our

  Stylish Beige Patio Roof

  This patio roof complements the exterior very well. The soft beige color provides a relaxed ambiance to the patio so that it can be a great place to call it a day.

  The pergola style allows natural light pass through which makes the patio shaded partially. You will not miss the warm of the sun when sitting in the patio.

  Step 4: Finishing Touches

  Side-roof-trims

  Use 1×4 lumber for the side trims. Make a 5 degree cut to one end of the trims. Attach the trims to the sides of the roof and lock it into place with 2 1/2 screws. See plans for a 12×16 pergola on my blog, as well.

  Lean-to-patio-cover-plansdiy

  This wooden attached patio pergola is easy to build and I can assure you this will dramatically upgrade your property.

  How-to-build-a-patio-cover-with-lean-to-roof

  You can easily transform this into an attached pergola, if you dont fit the purlins and the metal roof panels. You might also want to see.

  Patio-coverdimensions

  This patio cover features a metal sheet roof, so you can make it water proof while enjoying your time in the garden. If you are like me, the patio will become your new favorite place because you have fresh air and a cute roof over you head. Make sure you take a look over all my pergola plans HERE.

  Cost To Build A Covered Patio By Location

  

  Most patios are located beside the home. This makes them easily accessible and still leaves plenty of space for the rest of the yard and landscaping. But patios can be located elsewhere on the property, particularly if you want them located beside another feature like a pool, tennis court, or fountain.;

  The patio cover can also have different positions. If the patio is located beside the home, the cover can be either attached to the home, extending out over it, or it can be freestanding. When the patio is moved away from the home, the patio must be freestanding, limiting your choices for the cover. Both attached and freestanding covered patios have a wide range of costs because patios and covers come in many sizes and materials.

  Location
  $3,000 – $25,000

  Aluminum Patio Roof Cost

  The cost of an aluminum patio roof cover averages $20 to $70 a square foot installed. There are many different aluminum types for patios. You can find aluminum lattice, pergolas, and panels that come in several different gauges. Aluminum can be louvered, installed in slats, or combined with other materials. The thicker the aluminum, the longer-lasting its appearance but the higher its cost. Extruded aluminum costs more than rolled aluminum. Insulated aluminum costs more than extruded and rolled.

  Step 7: Finish The Job

  After that it was simple but repetitive work. I attached 1 x 6 boards to the top of the joists, and then screwed the corrugated metal roof to them. The most difficult part was getting the upper end of the metal sheets to go under the drip edge and roof decking of the house and to butt up against a bead of clear-drying roof cement I had put in there with a caulking gun. Also, putting a bead of sealer along the edge of the metal sheets before overlapping them was a bit demanding, though absolutely necessary.

  The job was done at that point. As for the corrugated metal roofing, I chose rubber washer metal-into-wood screws with ¼ bolt heads and used a ¼ magnetized drill adapted socket to put them in. That type of screw goes into every valley at the top and bottom ends of the panels and every other valley throughout the rest of the roof, into the 1 x 6 boards placed 24 on the center.

  
  
  Via https://www.lovemypatioclub.com/how-to-build-a-gable-roof-patio-cover/